Files

Plain Horse Rasps are double ended with rasp teeth on one side and file teeth on the other.

The edges are single cut.

Overall length: 350mm (14in).

PTDNICRHR14

Used by cabinet makers and woodworkers. Single cut on edges. Half-Round with the curved side having a larger radius than wood rasp.

Length 250mm (10in).

Half-Round Regular Cut Tanged.

PTDNICCR10

A 6 piece set packed in a wallet containing one of each 14cm needle files: Equalling, half-round, flat, round, square and three-square.

Cut: Fine.
Size: 5in.
Set of 6.

PTDNICMFSET

A rectangular shaped, tanged horse rasp, single cut on both edges with fine rasp teeth on one face and the special Magicut file teeth on the other.

Cuts much faster than conventional horse rasps.

Length is approximately 350mm (14in).
Tanged.

PTDNICMHR14

For general work on iron and steel. Slightly tapered in width and thickness. Double cut on both sides, and single cut on both edges.

Smooth Cut: approx. 62 teeth per 25mm (Fine).
Second Cut: approx. 36 teeth per 25mm (Medium).
Bastard Cut: approx. 26 teeth per 25mm (Coarse).

Size 200mm (8in)
Cut flat bastard
Tanged.

PTDNICFB8

For general work on iron and steel. Slightly tapered in width and thickness. Double cut on both sides, and single cut on both edges.

Smooth Cut: approx. 62 teeth per 25mm (Fine).
Second Cut: approx. 36 teeth per 25mm (Medium).
Bastard Cut: approx. 26 teeth per 25mm (Coarse).

Size 250mm (10in)
Cut flat bastard
Tanged

PTDNICFB10

For general work on iron and steel. Slightly tapered in width and thickness. Double cut on both sides, and single cut on both edges.

Smooth Cut: approx. 62 teeth per 25mm (Fine).
Second Cut: approx. 36 teeth per 25mm (Medium).
Bastard Cut: approx. 26 teeth per 25mm (Coarse).

Size 300mm (12in)
Cut flat bastard
Tanged.

PTDNICFB12

For general work on iron and steel slightly tapered in width and thickness.

Double cut on both sides, and single cut on both edges.

Size 150mm (6in)
Cut flat second
Tanged

PTDNICFSC6

For general work on iron and steel slightly tapered in width and thickness.

Double cut on both sides, and single cut on both edges.

Size 200mm (8in)
Cut flat second
Tanged

PTDNICFSC8

For general work on iron and steel.
Slightly tapered in width and thickness.
Double cut on both sides, and single cut on both edges.

Size 150mm (6in)
Cut flat smooth
Tanged

PTDNICFSM6

For general work on iron and steel.
Slightly tapered in width and thickness.
Double cut on both sides, and single cut on both edges.

Size 200mm (8in)
Cut flat smooth
Tanged

PTDNICFSM8

For general work on iron and steel.
Slightly tapered in width and thickness.
Double cut on both sides, and single cut on both edges.

Size 250mm (10in)
Cut flat smooth
Tanged

PTDNICFSM10

Cross section allows use on convex and concave surfaces. Tapered very slightly towards point both in width and thickness.

Smooth Cut: approx. 62 teeth per 25mm (Fine).
Second Cut: approx. 36 teeth per 25mm (Medium).
Bastard Cut: approx. 26 teeth per 25mm (Coarse).

Size. 100mm (4in)
Cut half round bastard
Flat Side: Double Cut
Half-Round: Double Cut.
Tanged

PTDNICHRB4

Cross section allows use on convex and concave surfaces. Tapered very slightly towards point both in width and thickness.

Smooth Cut: approx. 62 teeth per 25mm (Fine).
Second Cut: approx. 36 teeth per 25mm (Medium).
Bastard Cut: approx. 26 teeth per 25mm (Coarse).

Size. 150mm (6in)
Cut half round bastard
Flat Side: Double Cut
Half-Round: Double Cut.
Tanged

PTDNICHRB6

Cross section allows use on convex and concave surfaces. Tapered very slightly towards point both in width and thickness.

Smooth Cut: approx. 62 teeth per 25mm (Fine).
Second Cut: approx. 36 teeth per 25mm (Medium).
Bastard Cut: approx. 26 teeth per 25mm (Coarse).

Size. 200mm (8in)
Cut half round bastard
Flat Side: Double Cut
Half-Round: Double Cut.
Tanged

PTDNICHRB8