Hand Tools

The Moore & Wright 141 Series Dial Calipers have a hardened stainless steel covered rack and offer rapid movement with the thumb wheel. The calipers allow 4-way measurement and the measuring surface is micro-lapped.

The calipers are manufactured to DIN 862 standards.

The MW141-15 Dial Calipers have the following specification:

Range: 0-150mm.
Resolution: 0.02mm.

PTDMAW14115

The Moore & Wright Firm Joint Outside Calipers are manufactured from polished tool steel and have a large headed nut and screw assembly that provides a firm and rigid friction joint, with no play.

The sizes listed are the effective leg length which is measured from the joint assembly.

The Firm Joint Outside Calipers are manufactured to BS3123 standards.

Note: Firm joint caliper capacities are generally 1/3 greater than the effective leg length.

The Moore & Wright 3318 Firm Joint Outside Calipers have the following specification:

Size: 200mm (8in).

PTDMAW3318

The Moore & Wright Firm Joint Jenny Calipers are manufactured from polished tool steel and have a large headed nut and screw assembly that provides a firm and rigid friction joint, with no play. The leg which holds the round adjustable hardened point is offset and model 341 has a locating spur on the straight leg.

The sizes listed are the effective leg length which is measured from the joint assembly.

Note: firm joint caliper capacities are generally 1/3 greater than the effective leg length.

The Moore & Wright 341R Firm Joint Jenny Caliper has the following specification:

Size: 125mm (5in).

PTDMAW341R

The Moore & Wright Spring Dividers are manufactured from polished tool steel and the points are hardened to over 550Hv. The bow spring ensures uniform tension over working range and they are fitted with a centrally mounted adjustment screw.

These Spring Dividers comply with BS3123 standards.

Note: The nominal size is the distance between the centre of the roller and the working ends of the legs.

The Moore & Wright 506 Spring Dividers have the following specifications:

Size: 150mm (6in).

PTDMAW506R

The Moore & Wright 900 Series Internal Micrometers comprise of a measuring head, a set of extension rods and a spacing collar to facilitate alternative measuring ranges. These models (901, 902 & 903) have detachable extension handles.

All models supplied in a fitted case.

These 900 Series Internal Micrometers conform to BS959 Standards.

The Moore & Wright Internal Micrometer 901M Internal Micrometer has the following specification:

Range: 25-55mm.
Head Range: 5mm.

PTDMAW901M

The Moore & Wright 900 Series Internal Micrometers comprise of a measuring head, a set of extension rods and a spacing collar to facilitate alternative measuring ranges. These models (901, 902 & 903) have detachable extension handles.

All models supplied in a fitted case.

These 900 Series Internal Micrometers conform to BS959 Standards.

The Moore & Wright Internal Micrometer 903M Internal Micrometer has the following specification:

Range: 50-310mm.
Head Range: 10mm.

PTDMAW903M

The Moore & Wright Safe & Sure Feeler Gauge with hardened, tempered and polished blades. The nominal thickness is marked on each blade. Ideal for general workshop use.

The 911 Safe & Sure Feeler Gauge Set has the following specification:

Length: 4in
Width: 0.5in
Locking Screw: No
No. of Blades: 10

PTDMAW911

The Moore & Wright Safe & Sure Feeler Gauge with hardened, tempered and polished blades. The nominal thickness is marked on each blade. Ideal for general workshop use.

The 911M Safe & Sure Feeler Gauge Set has the following specification:

Length: 100mm
Locking Screw: No
No. of Blades: 10

PTDMAW911M

The Moore & Wright Safe & Sure Feeler Gauge with hardened, tempered and polished blades. The nominal thickness is marked on each blade. Ideal for general workshop use.

The 912 Safe & Sure Feeler Gauge Set has the following specification:

Length: 3in
Width: 0.5in
Locking Screw: No
No. of Blades: 10

PTDMAW912

The Moore & Wright CSM Precision Rules are fully hardened and tempered precision rules with deeply etched graduations on both sides for ease of reading and long life.

Theseare rules specifically designed for use with the Combination Sets (MAWCSM300 & MAWCSME12).

The Moore & Wright CSRME24 is a 600mm/24in rule is perfect for use with the combination sets and is graduated on both sides.

Measurements: Metric Graduations: in 0.5mm, numbered every 10mm. Imperial Graduations: 32nds and 64ths numbered every 1/8in.

PLEASE NOTE This is ONLY the Rule.

PTDMAWCSRME24

The Moore & Wright 100 Series Vernier Calipers have a standard workshop model design. They are made of hardened alloyed stainless steel and have a chromed scale with engraved graduations. The calipers allow 4-way measurement and the measuring surface is micro-lapped.

The calipers are manufactured to DIN 862 standards.

Supplied in a plastic box.

The MAW10030BI calipers have the following specifications:

Range: 0-300mm (0-12in).
Resolution: 0.02mm (0.001in).

PTDMAW10030BI

The Moore & Wright 141 Series Dial Calipers have a hardened stainless steel covered rack and offer rapid movement with the thumb wheel. The calipers allow 4-way measurement and the measuring surface is micro-lapped.

The calipers are manufactured to DIN 862 standards.

The MW141-15L Dial Caliper has the following specification:

Range: 0-6in.
Resolution: 0.001in.

PTDMAW14115I

The Moore & Wright Traditional External Micrometer has a blue textured frame finish with tungsten carbide measuring faces and a tapered bow frame. The speeder type ratchet, locking lever and adjusting key make this micrometer easy to use. It has a 6.5mm spindle diameter.

The micrometers are manufactured to BS870, DIN 863/1, ISO 361 standards.

Supplied in plastic pocket case.

The 1965 Traditional External Micrometer has the following specification:

Micrometer Range: 0-1in.
Measuring Faces: Flatness: 0.00005in, Parallelism: 0.0001in, Accuracy: 0.0001in.
Resolution: 0.001in.

PTDMAW1965

The Moore & Wright 966 Series Traditional External Micrometer has a blue textured frame finish with tungsten carbide measuring faces. The speeder type ratchet, locking lever and adjusting key make this micrometer easy to use. It has a 6.5mm spindle diameter.

The micrometers are manufactured to BS870, DIN 863/1, ISO 361 standards.

Supplied in a case.

The 1966/2 Traditional External Micrometer has the following specification:

Micrometer Range: 1-2in.
Measuring Faces: Flatness: 0.00005in, Parallelism: 0.0001in, Accuracy: 0.0001in.
Resolution: 0.001in.

PTDMAW19662

The Moore & Wright Protractor Type Depth Gauge has a full range rule adjustment and the readings can be fixed by means of a locknut. Rules are graduated on both sides.

Protractor plate is graduated 0 - 180 - 0.
Scale Resolution: 1/2.

The Moore & Wright 44 Protractor Type Depth Gauge Metric/Imperial has the following specifications:

Size of Base: 79mm/3.11in.
Width: 5.5mm/0.22in.
Thickness: 1.0mm/0.04in.
Length of Blade: 195mm/7.68in.

Metric/Imperial Scale Graduations : Front Face: 1/32nd, Rear Face: 1.0mm.

PTDMAW44