Electronic Cutters & Nipper Pliers

These Lindstrom Diagonal cutting nippers have an oval head. They are produced from high performance ball bearing steel which is black oxidised for increased durability. The numerically controlled machine grinding guarantees edge and angle accuracy and contact, which increases tool reliability and consistency.

The edges are precision induction hardened to 63-65 HRC. The handles have a return spring and are sleeved.

Ideal for wire harness work, and standard printed circuit board assembly.

Oval heads are the most common type of nipper head. It combines strength and durability, can withstand and distribute the impact of cutting and is utilised in a myriad of applications.

Length (A): 110mm (4.3/8 in)
Blade length (B): 10mm (0.39 in).
Head width (C): 10mm (0.39 in).
Head depth (D): 6mm (0.24 in).
Tip width: (F): 0.8mm (0.03 in).
Cutting Capacity: 0.1-1.25mm.

Cutting edge: Flush Bevel.

The Flush Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are pinched, allowing less altitude and a smaller overall surface area more than Micro-bevel cuts. The cutters have fine cutting edges that leave a narrow and short taper and small exposed area. They can be used to meet tight specifications for a flush result to a board, component or part.

PTDLIN8141

These Lindstrom Diagonal cutting nippers have an oval head. They are produced from high performance ball bearing steel which is black oxidised for increased durability. The numerically controlled machine grinding guarantees edge and angle accuracy and contact, which increases tool reliability and consistency.

The edges are precision induction hardened to 63-65 HRC. The handles have a return spring and are sleeved.

Ideal for wire harness work, and standard printed circuit board assembly.

Oval heads are the most common type of nipper head. It combines strength and durability, can withstand and distribute the impact of cutting and is utilised in a myriad of applications.

Length (A): 112mm (4.1/2in).
Blade length (B): 12.5mm (0.5 in).
Head width (C): 12.5mm (0.5 in).
Head depth (D): 6.0mm (0.24 in).
Tip width: (F): 1.2mm (0.05 in).
Cutting capacity: 0.3-1.6mm.

Cutting edge: Micro-bevel.

The Micro-Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are pinched, allowing less altitude and a smaller overall surface area. Because of its design, it has a wide cutting range and variety of uses.

PTDLIN8150

The Lindstrom Supreme Oblique Cutting Nipper produced from high performance tool steel. It has a screw joint that minimises friction and alignment of cutting edges.

The edges are precision induction hardened to 58-60 HRC. The handles with return spring and sleeved.

Length (A): 108mm (4.25 in).
Blade length (B): 8mm (0.31 in).
Head width (C): 10.5mm (0.41 in).
Head depth (G): 15mm (0.59 in).
Cutting capacity: 0.35-1.25mm.

Head type: Double angled.
Cutting edge: Micro-bevel.

Angled heads, also known as oblique style, are set at an angle to the main body of the cutter. This means that the cutter can reach between parts and areas which are difficult to access.

The Micro-Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are pinched, allowing less altitude and a smaller overall surface area. Because of its design, it has a wide cutting range and variety of uses.

PTDLIN7290

The Lindstrom Supreme Oblique Cutting Nipper produced from high performance tool steel. It has a screw joint that minimises friction and alignment of cutting edges.

The edges are precision induction hardened to 58-60 HRC. The handles with return spring and sleeved.

Length (A): 108mm (4.25 in).
Blade length (B): 8mm (0.31 in).
Head width (C): 10.5mm (0.41 in).
Head depth (G): 15mm (0.59 in).
Cutting capacity: 0.35-1.25mm.

Head type: Double angled.
Cutting edge: Flush.

Angled heads, also known as oblique style, are set at an angle to the main body of the cutter. This means that the cutter can reach between parts and areas which are difficult to access.

The Flush Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are pinched, allowing less altitude and a smaller overall surface area more than Micro-bevel cuts. The cutters have fine cutting edges that leave a narrow and short taper and small exposed area. They can be used to meet tight specifications for a flush result to a board, component or part.

PTDLIN7291

Lindstrom 7890 Supreme Flat Nose Pliers are produced from high performance tool steel. These holding pliers have a screw joint that minimises friction and maximises alignment of cutting edges. The handles have a return spring and are sleeved.

The smooth jaws minimise the risk of damage and scratching surfaces.

Length (A): 132mm (5.2 in).
Jaw length (B): 32mm (1.26 in).
Head width (C): 9mm (0.35 in).
Head depth (D): 6mm (0.24 in).
Tip width (E): 1.2mm (0.05 in).
Tip depth (F): 0.8mm (0.03 in).

PTDLIN7890

These Lindstrom Diagonal cutting nippers have an oval head. They are produced from high performance ball bearing steel which is black oxidised for increased durability. The numerically controlled machine grinding guarantees edge and angle accuracy and contact, which increases tool reliability and consistency.

The edges are precision induction hardened to 63-65 HRC. The handles have a return spring and are sleeved.

Ideal for wire harness work, and standard printed circuit board assembly.

Oval heads are the most common type of nipper head. It combines strength and durability, can withstand and distribute the impact of cutting and is utilised in a myriad of applications.

Length (A): 110 mm (4.3/8 in).
Blade length (B): 10mm (0.39 in).
Head width (C): 10mm (0.39 in).
Head depth (D): 6mm (0.24 in).
Tip width: (F): 0.8mm (0.03 in).
Cutting Capacity: 0.1-1.0mm.

Cutting edge: Ultra flush.

The Ultra flush cutter virtually eliminates the pinch that other cutters make. The cutters configure two flat planes, with a barely discernible line separating each of these planar surfaces. They are perfect for use in close tolerance electronic and medical device assembly, where concerns about final lead-end configuration and mechanical shock transmission are a top priority.

PTDLIN8142

These Lindstrom Supreme Flat Nose Pliers are produced from high-performance tool steel. These holding pliers have a screw joint that minimises friction and maximises alignment of cutting edges. The handles have a return spring and are sleeved.

The pliers smooth jaws minimise the risk of damage and scratching to the wire.

Length (A): 120mm (4.72in).
Jaw length (B): 20mm (0.79in).
Head width (C): 9mm (0.35in).
Head depth (D): 6mm (0.24in).
Tip width (E): 1.2mm (0.05in).
Tip depth (F): 3.2mm (0.13in).

PTDLIN7490

The Knipex 35 Series Precision Pliers with 2-component, soft-grip handles. For very fine installation work in electronics and fine mechanics. Used for gripping, folding and bending. Ground gripping surfaces with edges carefully deburred. Low friction double spring for gentle smooth closing and opening. The polish or mirror polish, together with a fine film of oil, offer effective rust protection - no circuit faults caused by peeling chrome from plated tools.

There are 3 versions in the 35 series - flat nosed, half round and round nosed. They all have precision shaped tips which are ideal for cutting close sitting wire from 0.2mm diameter.

Flat rectangular jaws.

PTDKPX3512115

The Knipex 35 Series Precision Pliers with 2-component, soft-grip handles. For very fine installation work in electronics and fine mechanics. Used for gripping, folding and bending. Ground gripping surfaces with edges carefully deburred. Low friction double spring for gentle smooth closing and opening. The polish or mirror polish, together with a fine film of oil, offer effective rust protection - no circuit faults caused by peeling chrome from plated tools.

There are 3 versions in the 35 series - flat nosed, half round and round nosed. They all have precision shaped tips which are ideal for cutting close sitting wire from 0.2mm diameter.

Half round jaws.

PTDKPX3522115

These Knipex 35 22 precision electronics half round jaw pliers with ESD grip to discharge the electrostatic energy correspondingly slowly and under control to protect endangered components. For very fine installation work in electronics and fine mechanics used for gripping, folding and bending.

Smooth ground gripping surfaces with carefully deburred edges. Low friction double spring for gentle smooth closing and opening. Mirror polish, together with a fine film of oil offer effective rust protection - no circuit faults caused by peeling chrome from plated tools.

Length: 115mm.

PTDKPX3522ESD

The Knipex 35 Series Precision Pliers with 2-component, soft-grip handles. For very fine installation work in electronics and fine mechanics. Used for gripping, folding and bending. Ground gripping surfaces with edges carefully deburred. Low friction double spring for gentle smooth closing and opening. The polish or mirror polish, together with a fine film of oil, offer effective rust protection - no circuit faults caused by peeling chrome from plated tools.

There are 3 versions in the 35 series - flat nosed, half round and round nosed. They all have precision shaped tips which are ideal for cutting close sitting wire from 0.2mm diameter.

Pointed round jaws for bending wire eyes.

PTDKPX3532115

These Knipex 35 32 Series precision electronics round nose pliers with ESD grip to discharge the electrostatic energy correspondingly slowly and under control to protect endangered components. For very fine installation work in electronics and fine mechanics used for gripping, folding and bending.

Smooth ground gripping surfaces with carefully deburred edges. Low friction double spring for gentle smooth closing and opening. Mirror polish, together with a fine film of oil offer effective rust protection - no circuit faults caused by peeling chrome from plated tools.

Length: 115mm.
Pointed Round Jaws for bending wire eyes.

PTDKPX3532ESD

These Knipex diagonal end cutting nippers are top quality precision pliers for ultra fine cutting work, in electronics and fine mechanics.

There are 2 versions in the 64 range - a 120mm 15 Angled head, and a 115mm 27 Angled head. Both versions have precision shaped tips which are ideal for cutting close sitting soft wire up to 1.5mm in diameter.

These Knipex electronic pliers are jointed with a stainless steel rivet for added strength and easy movement. The cutting edges are additionally induction hardened for durability and a longer life.

These pliers have an extremely smooth, play-free joint with a stainless steel rivet for minimum operator fatigue. The handles are coated with soft plastic which is easy on the hand.

Both models have precision-ground cutting edges for flush cutting and low friction double spring for gentle smooth closing and opening. The cutting edges are separately induction hardened to approximately 56HRc. They are made from special tool steel which is oil hardened for added strength and durability and have polished heads.

Length: 120mm.
End diagonal cutter with small bevel - 15 .

PTDKPX6432120

These Knipex diagonal end cutting nippers are top quality precision pliers for ultra fine cutting work, in electronics and fine mechanics.

There are 2 versions in the 64 range - a 120mm 15 Angled head, and a 115mm 27 Angled head. Both versions have precision shaped tips which are ideal for cutting close sitting soft wire up to 1.5mm in diameter.

These Knipex electronic pliers are jointed with a stainless steel rivet for added strength and easy movement. The cutting edges are additionally induction hardened for durability and a longer life.

These pliers have an extremely smooth, play-free joint with a stainless steel rivet for minimum operator fatigue. The handles are coated with soft plastic which is easy on the hand.

Both models have precision-ground cutting edges for flush cutting and low friction double spring for gentle smooth closing and opening. The cutting edges are separately induction hardened to approximately 56HRc. They are made from special tool steel which is oil hardened for added strength and durability and have polished heads.

Length: 115mm.
End oblique cutter, short head with small bevel 27 .

PTDKPX6442115

The Knipex 75 02 125 extra slim diagonal cutters are constructed from solid style forged top quality steel with precision non-slip tips for added strength and durability. With high quality material and precise workmanship for long service life. Clean cutting at cutting edge tips for hard or soft wire or thin copper wires. With narrow head style for use in confined areas.

Like most of the Knipex range of pliers, all components have oil hardened edges and hardened electric steel forged to approximately 64 HRc. They are ideal for cutting soft wire close to a flat surface with the bevelled blade. The cutters have a hardened head and plastic PVC coated cushion grip handles for added durability and comfort.

Length: 125mm.
Cutting Capacity: Piano: 0.4mm, Hard: 0.6mm, Medium: 1.0mm, Soft: 0.2-1.3mm.

PTDKPX7502125