Electronic Cutters

These Lindstrom Diagonal cutting nippers have an oval head. They are produced from high performance ball bearing steel which is black oxidised for increased durability. The numerically controlled machine grinding guarantees edge and angle accuracy and contact, which increases tool reliability and consistency.

The edges are precision induction hardened to 63-65 HRC. The handles have a return spring and are sleeved.

Ideal for wire harness work, and standard printed circuit board assembly.

Oval heads are the most common type of nipper head. It combines strength and durability, can withstand and distribute the impact of cutting and is utilised in a myriad of applications.

Length (A): 110 mm (4.3/8 in).
Blade length (B): 10mm (0.39 in).
Head width (C): 10mm (0.39 in).
Head depth (D): 6mm (0.24 in).
Tip width: (F): 0.8mm (0.03 in).
Cutting Capacity: 0.1-1.0mm.

Cutting edge: Ultra flush.

The Ultra flush cutter virtually eliminates the pinch that other cutters make. The cutters configure two flat planes, with a barely discernible line separating each of these planar surfaces. They are perfect for use in close tolerance electronic and medical device assembly, where concerns about final lead-end configuration and mechanical shock transmission are a top priority.

PTDLIN8142

These Lindstrom Diagonal cutting nippers have an oval head. They are produced from high performance ball bearing steel which is black oxidised for increased durability. The numerically controlled machine grinding guarantees edge and angle accuracy and contact, which increases tool reliability and consistency.

The edges are precision induction hardened to 63-65 HRC. The handles have a return spring and are sleeved.

Ideal for wire harness work, and standard printed circuit board assembly.

Oval heads are the most common type of nipper head. It combines strength and durability, can withstand and distribute the impact of cutting and is utilised in a myriad of applications.

Length (A): 110mm (4.3/8 in)
Blade length (B): 10mm (0.39 in).
Head width (C): 10mm (0.39 in).
Head depth (D): 6mm (0.24 in).
Tip width: (F): 0.8mm (0.03 in).
Cutting Capacity: 0.1-1.25mm.

Cutting edge: Flush Bevel.

The Flush Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are pinched, allowing less altitude and a smaller overall surface area more than Micro-bevel cuts. The cutters have fine cutting edges that leave a narrow and short taper and small exposed area. They can be used to meet tight specifications for a flush result to a board, component or part.

PTDLIN8141

These Lindstrom Diagonal cutting nippers have an oval head. They are produced from high performance ball bearing steel which is black oxidised for increased durability. The numerically controlled machine grinding guarantees edge and angle accuracy and contact, which increases tool reliability and consistency.

The edges are precision induction hardened to 63-65 HRC. The handles have a return spring and are sleeved.

Ideal for wire harness work, and standard printed circuit board assembly.

Oval heads are the most common type of nipper head. It combines strength and durability, can withstand and distribute the impact of cutting and is utilised in a myriad of applications.

Length (A): 112mm (4.1/2in).
Blade length (B): 12.5mm (0.5 in).
Head width (C): 12.5mm (0.5 in).
Head depth (D): 6.0mm (0.24 in).
Tip width: (F): 1.2mm (0.05 in).
Cutting capacity: 0.3-1.6mm.

Cutting edge: Micro-bevel.

The Micro-Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are pinched, allowing less altitude and a smaller overall surface area. Because of its design, it has a wide cutting range and variety of uses.

PTDLIN8150

These Lindstrom Diagonal cutting nippers have an oval head. They are produced from high performance ball bearing steel which is black oxidised for increased durability. The numerically controlled machine grinding guarantees edge and angle accuracy and contact, which increases tool reliability and consistency.

The edges are precision induction hardened to 63-65 HRC. The handles have a return spring and are sleeved.

Ideal for wire harness work, and standard printed circuit board assembly.

Oval heads are the most common type of nipper head. It combines strength and durability, can withstand and distribute the impact of cutting and is utilised in a myriad of applications.

Length (A): 125mm (5 in).
Blade length (B): 16mm (0.63 in).
Head width (C): 16mm (0.63 in).
Head depth (D): 8mm (0.31 in).
Tip width: (F): 1.6mm (0.06 in).
Cutting capacity: 0.4-2.0mm.

Cutting edge: Micro-bevel.

The Micro-Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are pinched, allowing less altitude and a smaller overall surface area. Because of its design, it has a wide cutting range and variety of uses.

PTDLIN8160

The Lindstrom Supreme Oblique Cutting Nipper produced from high performance tool steel. It has a screw joint that minimises friction and alignment of cutting edges.

The edges are precision induction hardened to 58-60 HRC. The handles with return spring and sleeved.

Length (A): 108mm (4.25 in).
Blade length (B): 8mm (0.31 in).
Head width (C): 10.5mm (0.41 in).
Head depth (G): 15mm (0.59 in).
Cutting capacity: 0.35-1.25mm.

Head type: Double angled.
Cutting edge: Micro-bevel.

Angled heads, also known as oblique style, are set at an angle to the main body of the cutter. This means that the cutter can reach between parts and areas which are difficult to access.

The Micro-Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are pinched, allowing less altitude and a smaller overall surface area. Because of its design, it has a wide cutting range and variety of uses.

PTDLIN7290

The Lindstrom Supreme Oblique Cutting Nipper produced from high performance tool steel. It has a screw joint that minimises friction and alignment of cutting edges.

The edges are precision induction hardened to 58-60 HRC. The handles with return spring and sleeved.

Length (A): 108mm (4.25 in).
Blade length (B): 8mm (0.31 in).
Head width (C): 10.5mm (0.41 in).
Head depth (G): 15mm (0.59 in).
Cutting capacity: 0.35-1.25mm.

Head type: Double angled.
Cutting edge: Flush.

Angled heads, also known as oblique style, are set at an angle to the main body of the cutter. This means that the cutter can reach between parts and areas which are difficult to access.

The Flush Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are pinched, allowing less altitude and a smaller overall surface area more than Micro-bevel cuts. The cutters have fine cutting edges that leave a narrow and short taper and small exposed area. They can be used to meet tight specifications for a flush result to a board, component or part.

PTDLIN7291

These Lindstrom Diagonal cutting nippers have an oval head. They are produced from high performance ball bearing steel which is black oxidised for increased durability. The numerically controlled machine grinding guarantees edge and angle accuracy and contact, which increases tool reliability and consistency.

The edges are precision induction hardened to 63-65 HRC. The handles have a return spring and are sleeved.

Ideal for wire harness work, and standard printed circuit board assembly.

Oval heads are the most common type of nipper head. It combines strength and durability, can withstand and distribute the impact of cutting and is utilised in a myriad of applications.

Lindstrom Diagonal Cutting

Size: 110mm.
Type: Micro Bevel Nipper.

PTDLIN8140

The Lindstrom Supreme Oblique Cutting Nipper produced from high performance tool steel. It has a screw joint that minimises friction and alignment of cutting edges.

The edges are precision induction hardened to 58-60 HRC. The handles with return spring and sleeved.

Length (A): 109mm (4.29 in).
Blade length (B): 9mm (0.35 in).
Head width (C): 9mm (0.35 in).
Head depth (D): 6mm (0.24 in).
Tip width: (F): 1.0mm (0.04 in).
Cutting capacity: 0.2-1.25mm.

Head type: Tapered
Cutting edge: Micro-bevel.

The tapered head is the smallest of the standard cutting heads available. Not only does it taper on both sides, but also the underside is cut away, allowing the operater to gain access into some difficult areas.

The Micro-Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are pinched, allowing less altitude and a smaller overall surface area. Because of its design, it has a wide cutting range and variety of uses.

PTDLIN7190

Knipex Electronic Super Knips XL for ultra-fine cutting work, e.g. in electronics and fine mechanics and for cutting cable ties to length. With ground, very sharp cutting edges without bevel. Precision shaped tips cut wires resting on a board from 0.2mm.

They have a shear cut with controlled micro cutting edge misalignment for the most precise cutting of even the thinnest of wires and for a long service life. The joint features a stainless steel rivet with extremely smooth movement for minimum operator fatigue. Fitted with multi-component grips, an opening spring and opening limiter.

78 03 140: Made from INOX tool steel, approx. 54 HRC cutting edge hardness

78 61 140: Made from special tool steel, oil hardened in multiple stages. Approx. 64 HRC cutting edge hardness

The Knipex 78 03 140 Electronic Super Knips are made from INOX tool steel, approx. 54 HRC cutting edge hardness

Specification:

Length: 140mm
Cutting Capacity : Soft 0.2-2.1mm, Medium-Hard 1.2mm

PTDKPX7803140

These Knipex diagonal end cutting nippers are top quality precision pliers for ultra fine cutting work, in electronics and fine mechanics.

There are 2 versions in the 64 range - a 120mm 15 Angled head, and a 115mm 27 Angled head. Both versions have precision shaped tips which are ideal for cutting close sitting soft wire up to 1.5mm in diameter.

These Knipex electronic pliers are jointed with a stainless steel rivet for added strength and easy movement. The cutting edges are additionally induction hardened for durability and a longer life.

These pliers have an extremely smooth, play-free joint with a stainless steel rivet for minimum operator fatigue. The handles are coated with soft plastic which is easy on the hand.

Both models have precision-ground cutting edges for flush cutting and low friction double spring for gentle smooth closing and opening. The cutting edges are separately induction hardened to approximately 56HRc. They are made from special tool steel which is oil hardened for added strength and durability and have polished heads.

Length: 120mm.
End diagonal cutter with small bevel - 15 .

PTDKPX6432120

These Knipex diagonal end cutting nippers are top quality precision pliers for ultra fine cutting work, in electronics and fine mechanics.

There are 2 versions in the 64 range - a 120mm 15 Angled head, and a 115mm 27 Angled head. Both versions have precision shaped tips which are ideal for cutting close sitting soft wire up to 1.5mm in diameter.

These Knipex electronic pliers are jointed with a stainless steel rivet for added strength and easy movement. The cutting edges are additionally induction hardened for durability and a longer life.

These pliers have an extremely smooth, play-free joint with a stainless steel rivet for minimum operator fatigue. The handles are coated with soft plastic which is easy on the hand.

Both models have precision-ground cutting edges for flush cutting and low friction double spring for gentle smooth closing and opening. The cutting edges are separately induction hardened to approximately 56HRc. They are made from special tool steel which is oil hardened for added strength and durability and have polished heads.

Length: 115mm.
End oblique cutter, short head with small bevel 27 .

PTDKPX6442115

The Knipex 75 02 125 extra slim diagonal cutters are constructed from solid style forged top quality steel with precision non-slip tips for added strength and durability. With high quality material and precise workmanship for long service life. Clean cutting at cutting edge tips for hard or soft wire or thin copper wires. With narrow head style for use in confined areas.

Like most of the Knipex range of pliers, all components have oil hardened edges and hardened electric steel forged to approximately 64 HRc. They are ideal for cutting soft wire close to a flat surface with the bevelled blade. The cutters have a hardened head and plastic PVC coated cushion grip handles for added durability and comfort.

Length: 125mm.
Cutting Capacity: Piano: 0.4mm, Hard: 0.6mm, Medium: 1.0mm, Soft: 0.2-1.3mm.

PTDKPX7502125

The Knipex 77 12 Electronic diagonal cutter are a top quality precision cutters for ultra fine cutting work in electronics and fine mechanics. Has around head, bevelled with wire clamp and round head, NON-bevelled. They have precision shaped tips which are ideal for cutting close sitting wire, soft wire up to 1.6mm to hard wire up to 0.5mm diameter.

These Knipex electronic cutters are jointed with a stainless steel rivet for added strength and easy movement and have cutting edges additionally induction hardened for durability and a longer life.

These pliers have an extremely smooth play-free joint with stainless steel rivet movement for minimum operator fatigue. The handles are coated with soft plastic for comfort and a return spring built into the handle.

This model has a precision-ground cutting edges for flush cutting and low friction double spring for gentle smooth closing and opening. The cutting edges are separately induction hardened to approximately 62HRc. These pliers are made from special tool steel which is oil hardened for added strength and durability. With polished heads.

Length 115mm.
Cutting Capacity: Hard: 0.6mm, Medium: 1.2mm, Soft: 0.2-1.6mm.

PTDKPX7712115

The Knipex 77 22 Series electronic diagonal cutter with a round head, NON - Bevelled are a top quality precision pliers for ultra fine cutting work in electronics and fine mechanics. The non-bevelled 77 22 115 have precision shaped tips which are ideal for cutting close sitting wire, soft wire up to 1.6mm to hard wire up to 0.5mm diameter.

These Knipex electronic pliers are jointed with a stainless steel rivet for added strength and easy movement and have cutting edges additionally induction hardened for durability and a longer life. These pliers have an extremely smooth play-free joint with stainless steel rivet movement for minimum operator fatigue. The handles are coated with soft plastic for comfort and a return spring built into the handle.

Precision-ground cutting edges for flush cutting and low friction double spring for gentle smooth closing and opening. The cutting edges are separately induction hardened to approximately 62HRc. These pliers are made from special tool steel which is oil hardened for added strength and durability. With polished heads.

Length: 115mm.
Cutting Capacity: Medium: 1.0mm, Soft: 0.2-1.3mm.

PTDKPX7722115

The Knipex electronic Super Knips are top quality precision pliers for ultra fine cutting work, in electronics and fine mechanics.

There are two versions in the range and both have precision shaped tips which are ideal for cut close sitting wire from 0.2mm diameter.

These Knipex Super Knips are jointed with a stainless steel rivet for added strength and easy movement and have cutting edges which are additionally induction hardened for durability and longer life.

These knips have a play free joint with stainless steel rivet for extremely smooth movement and minimum operator fatigue. They have handles which are coated with soft plastic and restricted opening which is easy on the hand. Both models have precision-ground cutting edges without bevel for flush cutting and INOX - stainless steel cutting edge that has been hardened to approximately 54 HRC.

Precision ground blades without a bevel for mirror cutting. Precision shaped tips also cut attached wires from 0.2mm diameter.

Cutting edges hardness approximately 54HRC.
Material: INOX stainless steel. Length 125mm.
2 coloured, 2-component handles.

PTDKPX7803125