Tool Accessories

Galvanised finishing staples for use with Stanley Bostitch Pneumatic Finish Staplers.

PTDGRPBOSSX503515

These 23 gauge mini pins are headless fine wire pins that are indispensible for fine molding and trim work. As the pins are completely headless , the wood closes over them after driving eliminating the need for time consuming filling
They are also excellent for temporary tacking whilst glue dries, as they can be removed with little damage to the work.
For use with the Bostitch headless pinner.

PTDGRPBOS1061200SE

Flooring L Cleats for use with the Bostitch flooring nailer.

L Cleat Finish: Galvanised

PTDGRPBOSFLN150

Designed for high volume operation, coils contain large quantities of nails meaning that reloading down time can be kept to a minimum. You will find them in the pallet and crate, fencing, garden furniture and the construction industries.

All Coil Nails are Round Head nails.

Typically:

Coils of nails with diameters from 2.0 mm to 2.2 mm contain 350 nails.

Coils of nails with diameters from 2.5 mm to 3.1 mm. Contain 225 nails.

Roofing nail coils contain 120 nails, due to the extra large diameter of the head.

15 Collation angle

Ring shank nails have a series of rings punched into the surface of the shank. A difference in the diameter of the shank is produced making it even more difficult to withdraw the nail.

Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish.

Galvanising, or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.

For use with:

N57C-1CE heavy-duty Coil Nailer

N58C-1-E Coil Nailer

N58C-1-E Coil Nailer

N66C-2-E Coil Nailer

PTDGRPBOSN203R40G8

BT13 Series 18 gauge brown brad nails for use with the Bostitch brad nailer.

Finish nails (brads) are normally of a rectangular cross section instead of being round. Their diameters are less than the coil and stick nails, and are primarily used for finish and trim work in the construction and joinery industries.

PTDGRPBOSBT1300B1M

Finish nails and brads have heads that are rectangular. They are the same width as the shank, but the breadth of them is greater than the shank, ensuring that their holding power is enhanced. Applications include partition walls, shop and bar fitting, light framing and timber construction and most second fit applications.

For use with N62FN-1, N62FNB-E & N62FNK-2 models.

Note: This nail will also fit the N60FN and the N59FNK models.

Applications -
Partition walls, shop and bar fitting, light framing and timber construction and most second fit applications.

25 collation angle

PTDGRPBOSFN1520

Finish Nails have heads that are rectangular. They are the same width as the shank, but the breadth of them is greater than the shank. This ensures that their holding power is enhanced, but of course the pull through force is lower than for nails with larger, Round or Clipped Heads. Primarily used for finish and trim work in the construction and joinery industries.

PTDGRPBOSSB16125BK

Packs of 2000 Round head nails.

These plastic collated stick nails traditionally have a full round head, while only giving marginally better holding power to clipped head nails, they are preferred by the construction industry. Collation is angled at 21 to accommodate the overlapping heads.

Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater.

Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.

PTDGRPBOSRH2545G50

Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments.

28 Collation Angle

Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx. 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out.

(Remember only tools fitted with sequential trip should be used when working up a ladder).

Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them.

Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater.

Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish.

Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.

PTDGRPBOSS28050

High carbon Zinc Dichromate HCFN finish nail 15 gauge.
For use with Bostitch concrete block nailer.

PTDGRPBOSHCFN20

Bostitch Stanox staples are also known as 84 series.

For use with TU-216-84-E or other tools using 84 gauge.

PTDGRPBOS1840600E

BT Series galvanised 18 gauge brad fasteners for use with the Bostitch Finish Bradders. Joined with an adhesive coating that holds the brads together.

Finish nails (brads) are normally of a rectangular cross section instead of being round. Their diameters are less than the coil and stick nails, and are primarily used for finish and trim work in the construction and joinery industries.

PTDGRPBOSBT1315GA5

Bostitch FAC Series Flat Angle Coil Pattern Ring Coil Nails are designed for high volume operation. The coils contain large quantities of nails meaning that reloading down time can be kept to a minimum. You will find them used in the pallet and crate, fencing, garden furniture and the construction industries.

To Suit:

N71C-1-E, N75C-2-E, N80CB-1ML, N89C-1P-E, N89C-2K-E

All Coil Nails are Round Head nails.

Typically:

Coils of nails with diameters from 2.0 mm to 2.2 mm contain 350 nails.

Coils of nails with diameters from 2.5 mm to 3.1 mm. Contain 225 nails.

Roofing nail coils contain 120 nails, due to the extra large diameter of the head.

15 Collation Angle

Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish.

Galvanising, or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.

Finish: Bright.
Size: 3.1 x 65mm.
Box quantity: 5,400.

PTDBOSF310R65Q

Bostitch FAC Series Flat Angle Coil Pattern Ring Coil Nails are designed for high volume operation. The coils contain large quantities of nails meaning that reloading down time can be kept to a minimum. You will find them used in the pallet and crate, fencing, garden furniture and the construction industries.

To Suit:

N71C-1-E, N75C-2-E, N80CB-1ML, N89C-1P-E, N89C-2K-E

All Coil Nails are Round Head nails.

Typically:

Coils of nails with diameters from 2.0 mm to 2.2 mm contain 350 nails.

Coils of nails with diameters from 2.5 mm to 3.1 mm. Contain 225 nails.

Roofing nail coils contain 120 nails, due to the extra large diameter of the head.

15 Collation Angle

Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish.

Galvanising, or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.

Finish: Bright.
Size: 3.1 x 75mm.
Boz quantity: 5,400.

PTDBOSF310R75Q

Bostitch FAC Series Flat Angle Coil Pattern Ring Coil Nails are designed for high volume operation. The coils contain large quantities of nails meaning that reloading down time can be kept to a minimum. You will find them used in the pallet and crate, fencing, garden furniture and the construction industries.

To Suit:

N71C-1-E, N75C-2-E, N80CB-1ML, N89C-1P-E, N89C-2K-E

All Coil Nails are Round Head nails.

Typically:

Coils of nails with diameters from 2.0 mm to 2.2 mm contain 350 nails.

Coils of nails with diameters from 2.5 mm to 3.1 mm. Contain 225 nails.

Roofing nail coils contain 120 nails, due to the extra large diameter of the head.

15 Collation Angle

Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish.

Galvanising, or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.

Finish: Galvanised Ring Shank.
Size: 3.1 x 90mm.
Box quantity: 4,050.

PTDBOSF310R90GQ