Tool Accessories

Chamfer V-grooving cutters are used for bevelling, chamfering and producing mortar grooves.

Due to design, an approx. 1.0 mm flat will be found on the nose.

Typical trade applications include sign making, freehand engraving, cabinet making and decorative joinery.

PTDGRPTRE11314HS

These cutters are used extensively for routing edge moulds, face grooves, columns, fluting, water slots, engraving and panel moulds in products such as desk tops, fire surrounds, draining boards and picture frames.

These cutters are suitable for use on all natural timbers and man-made boards.

PTDGRPTRE12314TC

These cutters are suitable for grooving, rebating, morticing and drilling. The single flute cutters offer fast free cutting. If you require a cleaner cut please use two flute cutters.

The depth of cut on cutters of 2.0mm diameter and below should be a maximum of 1.0mm per pass.

Small diameters in Tungsten Carbide must be handled with care to avoid breakage and very shallow passes must be made. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods

Single flute cutters must not be used in eccentric chucks.
Shank: 1/4in.

PTDGRPTRE20114TC

These plug cutters are designed to exactly fit the counterbored holes produced by group 62 and 63 Trend cutters.

Recommended speed - 1,000-20,000 /min.

PTDGRPTRE241014TC

Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling.

Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods.

Two flutes give a clean finish to cut edges.

1/4in Shank.

PTDGRPTRE30114TC

Two flute straight cutters produce a cleaner finish than the single flute cutters and are suitable for grooving, rebating, morticing and drilling.

Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood and certain hardwoods.

T.C.T. Tooling
1/2in Shank.

PTDGRPTRE48012TC

Trend dovetail cutters are designed for use with commercial dovetailing and stair housing jigs.

Also cutters to produce sliding and lapped dovetails, through dovetails and end on dovetails.

Suitable for use on natural timbers and man-made boards, they are used extensively in cabinet work, furniture making, stair trenching, dovetail jointing and carcass construction.

PTDGRPTRE310214TC

Trend two flute hinge jig cutters with extra long shanks for deep grooving, rebating and morticing which are useful for template work when thickness of template restricts depth.

Extra care must be taken to avoid breakage. Take more passes than usual and only cut up to half the diameter of the cutter in one pass.

PTDGRPTRE320L14TC

342 Biscuit jointer set enables biscuit jointing with timber, man-made fibre and particle board with the router.

The set includes three sizes of bearing to suit biscuits available.

The correct choice of bearing for the biscuit being used will ensure the correct depth of cut.

A step washer is supplied for use with bearings Ref B15, and B23.

A slightly wider cut than the width of the biscuit is required to allow some lateral play for easy alignment during assembly.

PTDGRPTRE34214TC

These Cutters produce recesses with a lower rebate - double rebate.

Designed to accept library/bookcase strip (Tonk Strip).

PTDGRPTRE361014TC

Self-guiding cutters with bearings mounted for trimming and bevelling timber, lippings and plastic laminate edges for cabinet making, countertop production or any shaping applications.

Bearing guided cutters are suitable for both straight and curved work, bearings are normally fractionally larger than cutter diameter, to avoid surface scoring.

Uses:
Trimming plastic or plywood overlay.
Copy profiling - use the bearing to follow a template or base edge of board.

A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing.

Tooling Tungsten Carbide
1/2in Shank.

PTDGRPTRE46214TC

Profilers with shank mounted bearings for guidance, for use with router mounted above or below a table when following a template. Bearing guided cutters are suitable for both straight and curved work.

For profiling and rebating applications only. NOT for plunge, cutting or grooving.

A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing.

PTDGRPTRE469412TC

Ovollo and rounding over bearing guided cutters are ideal for curved work, they can be used on natural timbers, man-made particles and fibre boards.

Popular uses include edging window frames, glazing bars, cabinets, table tops, pencil rounds, trophies, shelves and fire surrounds. They can also be used to produce bullnose edge moulds.

All cutters supplied with two bearings, larger bearing removes the quirk producing a round over profile.

PTDGRPTRE461712TC

These types of cutters are used for edging work and chamfer cutting on man made fibre boards, natural timbers and plastics. Tools are offered to produce various angles for chamfering.

Ball bearing and pin guarded cutters enable curved work to be undertaken with bearings running along the board edge or a template. Typical trade applications include sign making, freehand engraving, cabinet making and decorative joinery.

PTDGRPTRE463714TC

Popular rebate sets which include different size bearings for a choice of rebates. They provide easy setting up and accurate depth of cut.

Ideal for rebating straight and shaped work pieces .

Tooling TCT.

By changing the bearing the size of the rebate can be altered.
Supplied with four bearings.
19 mm Bearing gives rebate of 7.9 mm
16 mm Bearing gives rebate of 9.5 mm
12.7 mm Bearing gives rebate of 11.1 mm
9.5 mm Bearing gives rebate of 13.7 mm
D = 35 mm
C = 12.7 mm

PTDGRPTRE463912TC